URSA 10 Loft Roll
Services Tanks, pipes, vessels and ducts in the roof void must be insulated to avoid freezing and/or Figure 5 – Loft Insulation Upgrade URSA 10 Loft Roll top up (if required) and overlay Sarking felt (if The second layer of URSA 10 Loft Roll , minimum 170mm thick, is laid at right angles to the joists … Retrieve Full Source

Torch On Data Sheets (400's):Layout 1
Available to suit 80, 100 & 120mm pipes. Angle Fillet Angle fillets are to be used to reduce the 90º One size fits all 200mm 80/100/120mm 380mm 380mm 1000mm 40mm 40mm 380mm 170mm 170mm 340mm 340mm 200mm 200mm 200mm use with Euro Polymers Diamond & Sapphire SBS and APP Systems TD Underlay – Vapour Barrier and Insulation … Retrieve Doc

BUILDING REGULATIONS
36.33 deg. GROUND FLOOR – FIRST FLOOR TO ANNEX STAIRCASE ADJACENT GARAGE Floor to Floor level = 2720mm 16 No. Risers at 170mm FIRST FLOOR Beam and block floor of main house to Structural Engineers design and detail. 65mm screed over 65mm min. Insulation with cut outs for underfloor heating pipes … Retrieve Document

Extension Specifications, 23 Nightingale Avenue
Surrounding membranes/tapes) 100mm dense concrete block 170mm spec (47×145 @600mm centres) Full joist depth breathable insulation foam-cored section door To be done by householder Garage insulation Fit 100mm PUR and sheathing To be done by householder Underfloor heating (pipe lay only) Lay pipes … Fetch Full Source

FLEXIBLE LINERS & FLUE BOXES
A gas flue terminal must be fitted to an all gas installations of 170mm diameter or less. plate (4002) Turboflex Plus (TBP11) VE Adaptor to Turboflex Plus Bottom support bracket fixed to masonry (4009) Airbrick or vent Ventilated air space or insulation … Access Document

The Next Generation
TECHNICAL DATA Size: 500mm x 330 mm x 170mm Connections: 25mm MDPE (Philmac type) Barrier pipe(s) 25mm Injection moulded in 100% reprocessed polypropylene material UV stabilised 50+ year design life Insulation Range" on smart meter extended by 10x • No leakage from joints in service pipes • No excavations … Document Viewer

Work Station Series For Solar Water Heating Control System
Heating control system 3 2 Main technical data Dimension: 520×290×170mm System design pressure: 1 MPa Safety valve respond pressure: 0.6 MPa WILO pump model: SR25/6, SR15/6 (For choice) Screw coupling: 3/4〞 Thermal insulation Use two wrenches to connect the pipes. See picture. … Fetch Content

Building Control Guidance Note
The ceiling joists and 170mm over the top at 90 o to lower insulation. It can easily be done as a DIY project, Insulate pipes in the loft to stop them freezing and bursting in cold weather. … View Full Source

EP 250×240 Brochure (Digital Sept '10):Layout 1
Side Laps: Minimum 100mm Head Laps: Minimum 150mm FIXING INSULATION 1 Loose lay the TD Underlay on the deck Available to suit 80, 100 & 120mm pipes. Angle Fillet Angle fillets are to be used to reduce the 90º COMPATIBLE WITH ALL EUROTORCH GUARANTEED SYSTEMS 200mm 80/100/120mm 380mm 380mm 1000mm 40mm 40mm 40mm 170mm … Fetch Content

12.00 FLAT ROOF OUTLETS
Not for use with 170mm or 200mm gutter. Side Rafter Bracket Code Colours R16 Galv Supplied with wing nut and bolt. Not for use with 170mm or 200mm gutter. … Read Document

Www.everbuild.co.uk
Available in two sizes 230mm x 170mm x 4mm and 170 x 170mm x 4mm FIRESPAN INTUMESCENT PADS fit Do not use in areas subject to prolonged high temperatures i.e. central heating pipes, ducting Silicone Rubber Polymer Containing intumescent Fillers – yellow colour: Integrity /insulation … Document Retrieval

Building Control Guidance Note 6 – Pitched Roofs
Typical details being used at the moment include: Pitched Roofs (insulation at ceiling level) – 100mm of fibreglass between joists and a further 170mm across joists. A 50mm vented airspace above insulation is required. All water storage tanks and pipes within the roof space should be insulated. … View Document